Description of changes contained in version 3.15.2 (10/20/2015) Allow manually setting fan speed to 0 on RAC10. Allow internal temperature sensor on RAC10 to be ignored when external sensors are present. Improved handling of unplugged remote sensors on RAC10. Fixed SNMPv3 traps sent unencrypted. Fixed RAC10 units losing fan configuration on reboot when set to Temperature Set Point mode. Description of changes contained in version 3.15.1 (3/6/2015) Updated branding of environmental products. GRSE -> Watchdog 1250 GRSE-B -> Watchdog 1200 GRSO -> Watchdog 1400 GRSMINI163 -> Watchdog 1000 Updated web page color schemes to match Power/Cool/Monitor branding. Updated copyrights to 2015. Description of changes contained in version 3.12.7 (3/24/2014) Fixed units sometimes becoming unresponsive to network communications under heavy traffic load. Fixed network host name not getting updated after friendly name change via CLP. Fixed minor MIB formatting error. Description of changes contained in version 3.12.6 (12/17/2013) Added the ipForward.ipCidrRouteTable to SNMP. Added an SNMP enable/disable command to the CLP. Improved accuracy of phase current measurements on true delta RCX/M/U/O units. Fixed an issue that caused SNMP to respond slowly on some units. Fixed various SNMP entries not updating when the device's network address changed. Fixed an issue that could cause RCX/M/U/O units to lock up when using the serial CLP. Fixed an issue that could potentially make group amps on RCU-O and RCO units read 0. Fixed minor formatting issues in the CLP. Fixed a formatting error in the data.xml file on legacy (non -O) RCX/M/U units. Fixed an issue that could cause units not to reboot during the firmware update process. Note: This fix takes effect the next time the unit is updated after installing this firmware or newer. Reverting to firmware prior to 3.12.6 will reintroduce this issue. Updated copyrights to 2014. Description of changes contained in version 3.12.4 (9/5/2013) Added host name to CLP login prompt. Added internal sensors friendly name to CLP prompt. Added 'clock' commands to CLP. Added a space to CLP login prompt. Added NTP sync period to CLP 'report' command. Added uptime (in seconds) to CLP 'report' command. Added 'admin description' command to CLP. Added IP address and IP Address/Measurement scrolling to LCD options. Added time since last status change to RCM and RCU outlets in data.xml, CLP, and SNMP. Added time since last status change to RS2 outlets in data.xml and SNMP. Added network link state information to CLP. Added network link speed and uptime information to web, data.xml, CLP. Report actual link speed and uptime information in mib-2 interfaces table. Enabled device friendly name changes via CLP. Enabled renaming of IO ports via CLP on GRSE, GRSO, RSM, GRSMINI163, and GIOE. Enabled renaming of RFC external sensors via CLP. Enabled DM friendly name changes via CLP. Enabled renaming of T3HD internal/remote sensors via CLP. Fixed CLP printing extraneous units on T3HD external temperatures. Fixed newline formatting in various CLP messages. Fixed DM, GIOE, RSS, RTAFHD3, T3HD, THD, RS2 showing up as Unknown in the web interface and missing from SNMP if they were unplugged during bootup. Fixed an issue that could cause a DM to show up as "Too many DMs" and not show any data after a reboot. Fixed missing DM display pages for some remaining DMs when an active DM is unplugged and removed. Fixed GIOE reporting relay status twice instead of mode and status in data.xml. Fixed an issue that could cause T3HD sensors to remain in the "Unavailable" state forever. Fixed an error that prevented alarms from being set on some RCO/U outlets via SNMP. Fixed incorrect logos on some RAC10 web pages. Fixed IO ports all getting port 1 friendly name on reset defaults on GRSE, GRSO, and GRSMINI163 units. Fixed missing graphs for some external sensors on RAC10 units. Removed the RS2 disclaimer from the RFC's Config-Admin page since that device does not support external sensors except RTs. Removed outlet state and parameter printouts from CLP on RCO units. Disallow configuration of outlet delays (normal and POA) on RCO units via CLP. Changed ctrlOutletStatus, ctrlOutletFeedback, and ctrlOutletPending OIDs to return 1 when read on RCO units since the outlets are always on. Changed ctrlOutletStatus, ctrlOutletPending, and all delays to return not-writeable on RCO units. Changed data.xml uptime to report in seconds. Description of changes contained in version 3.12.1 (6/4/2013) Note: Due to firmware structure changes it is not possible to load firmware older than v3.12.1 onto units that have been upgraded to v3.12.1 or newer. Fixed CSV datalog not reporting Group Volts and/or returning a blank file on RCU and RCO units. Fixed missing outlet groups on some RCM/U/O units with more than 32 outlets. Description of changes contained in version 3.11.1 (3/28/2013) Added support for 48 outlet RCM-O, RCU-O, and RCO products. Fixed RCM, RCM-O, RCU, RCU-O, and RCO outlet names with special characters breaking data.xml. Fixed T3HD remote sensors reporting invalid values when measuring negative temperatures. Fixed spurious Relay Failure messages on RCU-OH units operating at 230V. Description of changes contained in version 3.9.8 (1/11/2013) Added support for new 60Vdc Sensor. Added a Reboot button to Config - Admin page. Note: This button does not affect outlets in switching units. They will remain in their current state through the reboot. Renamed RSE, RSE-B, RSMINI163, and RSO devices to GRSE, GRSE-B, GRSMINI163, and GRSO. Updated Chinese and Japanese translations. Updated copyrights to 2013. Description of changes contained in version 3.9.7 (11/19/2012) Fixed a problem where some high current (35A rated and higher) RCX/M/U/O units could under-report Amps, Watts, VA, and kWh by 2.5x after a firmware update. Note: If after this update your PDU is still reporting low current, please contact support. Fixed the graph color legend on the PDA page not matching the one on the Sensors page. Fixed DCS-6112 and DCS-2210 camera image links. Fixed CCAT sensors becoming nonresponsive in rare cases. Description of changes contained in version 3.9.6 (9/14/2012) Improved accuracy of RCX-D, RCM-OD, RCU-OD and RCO products running on 50Hz power. Note: This fix requires updating via ASU v1.11.1.6 or newer. Fixed a formatting error in the datalog.csv file. Added support for D-Link DCS-6112 and DCS-2210 cameras. Description of changes contained in version 3.9.5 (6/22/2012) Added Japanese translation. Added Average to logging modes. Updated Spanish, French, German and Chinese translations. Fixed a spacing issue on the RCO Control page. Improved RCX/RCM-O/RCU-O/RCO configuration validation checks. Description of changes contained in version 3.9.4 (5/11/2012) Added support for new RCO products. Added support for new GT3HD and GTHD sensors. Added "Board Error" and "Relay Error" to the "All's well" message in the web interface. Improved handling of RCM-O, RCU-O outlet error conditions. Extended Current Monitor and 30Vdc CCAT logging precision to 2 decimal places. Fixed web pages disappearing when certain languages were selected. Fixed an issue with custom camera URLs. Updated French translation. Updated Geist logo and contact information. Description of changes contained in version 3.9.1 (2/8/2012) Fixed RCX, RCM-O, and RCU-O units occasionally reporting very low voltage on Phase A for one measurement cycle. Fixed RCM-O and RCU-O devices reporting as RCX during early bootup. Fixed a memory leak when sending an SNMP trap fails. Camera passwords no longer shown in page source code for security reasons. Description of changes contained in version 3.9.0 (1/16/2012) Added alarm configuration via SNMP, see new alarmSystem table. Added alarmTrigger and alarmInstance to all SNMP traps. Improved speed of HTTPS in some browsers. Changed SNMP alarmTripType and temperaturePrecision to integer enumerations. Fixed page load errors when the browser's language is not natively supported. Fixed a potential loss of connectivity under heavy network traffic. Fixed errors in Geist Console when device's language is not set to English. Updated copyrights to 2012. Description of changes contained in version 3.8.1 (8/11/2011) Added automated switching of outlets via alarms on RS2s. Improve handling of some network errors. Improved compatibility with chatty email servers. Fixed broken powerMonitorCount and tempSensorCount entries in sensorCounts SNMP table. Fixed RSMINI163 analog I/O port traps being sent with wrong trap ID. Fixed RSE, RSE-B, RSMICRO relative humidity traps being sent with wrong trap ID. Description of changes contained in version 3.8.0 (6/15/2011) Added German, French and Chinese language translations. Added Total kWh and Total Real Power to RSS. Note: To reduce visual clutter these values are not displayed on the Sensors page of single-channel units but are shown on the Alarms page, Logging page, data.xml, SNMP and CLP for easy standardization of scripts and monitoring by 3rd party systems. Fixed SNMP sensorCounts table not responding properly to requests with .0 at the end of the OID. Email passwords no longer shown in page source code for security reasons. Apparent Power keys in data.xml changed from "Volt-Amps" to "ApPower" on true delta RCX, RCM-O and RCU-O units to match other devices. Description of changes contained in version 3.7.0 (5/13/2011) Added support for true Delta RCX, RCM-O, and RCU-O products. Added support for serial CLP on true Delta RCX, RCM-O, and RCU-O products. Added Total kWh and Total Real Power to WYE-mode RCX, RCM-O, and RCU-O products. Note: To reduce visual clutter these values are not displayed on the Sensors page of single-channel units but are shown on the Alarms page, Logging page, data.xml, SNMP and CLP for easy standardization of scripts and monitoring by 3rd party systems. Added support for D-Link DCS-930L and DCS-3411 cameras. Added "Delayed Reboot" to the outlet actions on RCM, RCM-O, RCU, and RCU-O products. Added support for "Cancel" outlet action in SNMP for RCM, RCM-O, RCU, and RCU-O products. Added support for "Reset kWh" outlet action in SNMP for RCM-O and RCU-O products. Renamed "reboot-delay" in data.xml to "reboot-duration". There is a new value for "reboot-delay" that defaults to 0 for backward compatibility. Improved handling of HTTP and HTTPS requests with large amounts of cookie data. Changed Trip Delay for alarms to a text box which accepts a range from 0 to 240 minutes. Renamed ctrlOutputCount to ctrlOutletCount in the MIB for consistency. Standardized on "kWh" and "kWatt" throughout the interface and MIB. Changed Apparent Power units to Volt-Amps. Removed RacControl references in the MIB. Fixed measurement unit details (“rms”) disappearing from the Sensors page after an AJAX update. Removed unused PowerOnly SNMP table and replaced it with ctrl3ChDELTA table for new true Delta RCX, RCM-O and RCU-O units. Fixed webpage language settings not saving properly. Fixed temperatures not showing up as alarmed on the Sensors page when the device’s temperature units don’t match the alarm’s. Fixed a problem where repeat and delay timers for alarms were not being properly cleared. Fixed borders on the Logging page in Webkit-based browsers (Chrome, Safari, Android, iOS, etc.) Fixed: User-set min/max values not showing up in the data.xml. Improved support for D-Link password protected cameras. Fixed CLP showing wrong DNS server addresses when in DHCP mode. The PDA image page now supports password protected images. Description of changes contained in version 3.6.1 (3/3/2011) Non-loggable measurements (kWh, Outlet Amps on RCU-O and DM meters) can now be shown on local and remote displays. Added user-defined scaling for analog I/O ports on RSE, RSM, RSMINI163, and IOE devices. Improved performance of IO Expander relay switching. RS2 devices now report possible relay failures more accurately. Fixed spurious errors on RTHD, RTAFH and RTAF sensors that could cause them to show up as "Unavailable" or "Unplugged". Fixed incorrect OID listings for DM meter SNMP CLEARs in the MIB. Fixed Time Range selection on the Logging page resetting after a page refresh. Fixed DHCP sometimes turning off after firmware updates. Fixed some minor interface inconsistencies. Description of changes contained in version 3.6.0 (1/26/2011) Sensors and Logging page automatically update measurements, time, graphs, camera thumbnails and “All is well” message without page refreshes. Graphs on the Logging page show changes immediately without a page refresh. Hit “Save Changes” to permanently store changes. Checkbox and radio button labels are now clickable. Improved reliability of RTHD, RTAFH, RTAFHD and RTAFHD-3 sensors. DST, NTP and HTTP/HTTPS port input fields are now hidden when those features are disabled. Added user-settable SNMP temperature precision, see Display page and MIB. Added a favicon for browser bookmarks. Added extra information to data.xml to improve support for Console 3.1.5. Added new options to the CLP “sensors” command. Fixed some RSMINI163s not responding to SNMP. Fixed some relay settings not being saved on RSO units. Fixed RSS max kWh set to 0.0 in data.xml. Fixed periodic email reports showing wrong IP address when unit received its IP address via DHCP. Fixed extraneous measurements showing up in alarms drop down list on RCX, RCM-O, RCU-O, RSS and DM units. Removed ‘-A’ labels from measurements on single-circuit/phase RSS units. Moved relay and outlet information in data.xml on RSO, RCM-O and RCU-O units for better consistency. Modified alarms section of data.xml for better readability and consistency. Changed alarm interface to a list of checkboxes for easier management. Changed email protocol configuration to a drop down box. Changed default SSL certificate from www.geistmfg.com to *.geistmfg.com. Updated copyrights to 2011. Description of changes contained in version 3.5.6 (11/12/2010) Added mouse over tooltips to some sensors page measurements. Added a check box for sending full or SMS-formatted email to each email recipient. Changed Alarms page interface to support future products Greatly improved Telnet command line protocol. Fixed SNMP Amps values on RSM being given in Amps, not deci-Amps. Fixed SNMP sysDescr not being set correctly on some devices. Changed alarm email subject and body to clarify device friendly name and sensor friendly name. Removed unnecessary syslog messages. Changed format of XML device 0 'type' attribute to clarify device capabilities. Product name Type string ---------------------------------------- RSE-B Clim-THLFSA3 RSE Clim-THLFSA3-DB RSMINI Clim-T RSMICRO Clim-TH RSO Clim-Rel-TA6-DB RSMINI163 Clim-TA3 RSM Clim-Pow-THLFSA3-DB RCX/RCM-O/RCU-O Pow-Swi-250-DB RCU-O Horizontal Pow-Swi-250-DBU Fan Controller Fan-DB Clim - Climate Monitoring Pow - Power monitoring Swi - Outlet switching Rel - Relay switching Fan - Fan control T - temperature L - light H - humidity F - airflow S - sound A[0-9]+ - analog (number represents count of inputs) D - LCD Display B - Buzzer U - Horizontal Variant (1U) Description of changes contained in version 3.5.1 (10/22/2010) Sensors page refreshes every 60 seconds. Fixed a bug that occurred when Smoke Alarm sensors are attached. Description of changes contained in version 3.5.0 (8/12/2010) Added support for new RTAFHD3 sensors. Finalized support for upcoming DM and RS2 products. Added a contextual help system. Click on ‘?’ to get help for an item. Fixed some sensors not showing up in SNMP. Fixed SNMP Traps missing variable bindings. Improved handling of camera IP address entry. Webcam thumbnails enlarged. Description of changes contained in version 3.4.5 (7/6/2010) Fixed incorrect Peak Amps readings on some RCU-O horizontal units. Description of changes contained in version 3.4.4 (6/22/2010) Fixed Digital Sensor always reading 0 in SNMP. Changed message on LCD when no measurements are displayed from "NO DATA" to "NONE SELECTED". Description of changes contained in version 3.4.0 (4/14/2010) NOTE: Due to changes in the measurement logging system updating to this firmware will erase your log history. Please download and save your log history prior to updating if you wish to maintain it. Improved Logging System: Does not lose data after a power cycle and provides greater flexibility for future improvements. Selective Logging Controls: Measurements can now be logged normally or using high/low-water marks. Alternately, logging can be disabled for individual measurements, increasing the available logging time. Remote Display: Measurements can now be shown on LCD displays regardless of their logging/graphing setting. Alarm Notification Repeat and Delay: Each alarm has a configuration option for the time it must be tripped before sending any notifications. Also, alarms can be set to repeat periodically until they clear. Email scheduling: Each email address can be setup to send alarms only within specified hours, outside of those hours or at all times. Non-volatile Event Log: Important events like alarm trips are now preserved in non-volatile memory for user review. Daylight Saving Time: Configuration of dates for daylight saving time is now supported. Multiple Languages: Web pages can now be dynamically changed from English to Spanish. Other languages will follow. New Product Support: Support for RS2 and DM meter devices has been added. Dew Point Measurement: Dew point has been added to the RSE, RSE-B, RSM and RSMICRO. Various other bug fixes and improvements. Description of changes contained in version 3.3.1 (12/7/2009) Fixed RSD2X8 not scrolling when attached to RCU-O units Fixed Idle and Activity lights not blinking on RCU-O units Various other bug fixes and improvements Description of changes contained in version 3.3.0 (11/5/2009) Added support for RCX products Added the ability to upload a custom SSL certificate and private key Added SNMP SET capability to ctrlOutletStatus on all RCM, RCU, RCM-O and RCU-O units Added an option on the Alarms page to stop nuisance sensor unplugged alarms Added 'uptime' variable to XML file Added timeouts to DNS lookups Improved the network configuration page Improved handling of usernames/passwords on non-supported cameras Improved speed of RCM, RCU, RCM-O and RCU-O data collection Fixed an issue where RCU and RCU-O units did not support outlet-level alarms Fixed power factor calculation on RCM, RCU, RCM-O and RCU-O units with multiple circuits Emails now retry up to 5 times before failing Removed extraneous error messages from syslog Slight changes to MIB and CSV files to allow simultaneous use of v2 and v3 devices Various other bug fixes and improvements